风挡防冰表面温度场计算

在研究国内外有关资料的基础上，采用了量纲分析的方法，建立了风挡外表面温度场的计算模型。回避了对自由流与射流相互干扰这一复杂问题的研究，同时对该计算模型进行了验证，并开发了相应的计算程序。该问题的解决，填补了国内在该领域中的空白。     

智能多通道测温仪

本文介绍以8031单片机为核心设计的智能多通道测温仪的构成、工作原理、程序设计以及温度传感器的非线性修正和仪器的精度分析。     

脉冲式转速表的设计,校验与应用

本文就航空发动机转速测量技术状态进行了简要分析,对适用于超轻型飞机的具有原理、结构简单,造价低等优点的“脉冲式转速表”的设计、校验等进行了详细的论述,并对该原理的推广应用进行了分析讨论。     

导弹燃气流瞬态温度测量系统设计

介绍了采用蓝宝石黑体腔光纤作为传感器的导弹燃气流瞬态温度测量系统的测量原理、系统组成,阐述了其硬件功能模块设计,给出了软件设计算法及蓝宝石黑体腔光纤高温计的标定方法。     

三维瞬态导热温度场边界元计算及一阶数学奇异的处理

推导了三维瞬态导热温度场边界元解法的积分方程和离散代数方程，并编制了相应的计算机程序，采用坐标变换的解析消去法，处理边界元的一阶数学奇异点，从而提高了算法的数值精度。用本程序计算了正方体和圆柱环瞬态导热温度场，数值解与解析解的吻合程度令人满意。     

喷口辐射热泄漏对延伸段壁温分布的影响

引入喷口的热辐射泄漏损失，导出辐射冷却推力室壁温的计算方程。分析表明，考虑与不考虑喷口热损失二者相比较，前者壁温约下降７０℃。本结果可为喷管延伸段材料的选取提供更为科学的理论依据。     

基于特征的锻件分类及特征有限元法

综合分析锻件后引入特征技术并归纳锻件的形状及变形特点 ,提出了锻件特征概念并给出锻件形状特征的一般定义和构成 ;采用面向对象技术表示特征 ,提出了锻件特征类的概念模式和具体的参数化数据模型 ;针对有限元分析中复杂多变的约束条件和载荷状况两个关键性因素的表达 ,提出特征类的关联思想。在基于特征的锻件分类基础上 ,把锻件变形归纳为“挤”或“压”两种特征元 ,提出了采用基于特征的有限元法 ,并综合自适应FEM、并行FEM、智能型FEM共同求解大型复杂锻件的变形模拟问题。     

含内热源球壳的复合传热特性及其表面温度均匀性研究

应用计算流体动力学方法,对带内热源的空腔球壳所涉及的含导热、自然对流和辐射换热的耦合传热问题进行了数值建模,得到了球壳空腔内、外侧流体的温度场、速度场。在数值模拟基础上,提出并试验验证了能有效提高球壳外表面温度均匀性的电加热绳方案。     

Effect of Counterface Material on Friction and Wear Behavior of Ni-Cr-W-Al-Ti-MoS_2 Composites

Ni-Cr-W-Al-Ti-MoS2 self-lubricating composites were prepared through the powder metallurgy (P/M) method. Their friction properties were investigated by a pin-on-disk tribometer in the range from the room temperature to 600 ℃. Alumina, silicon nitride and nickel-iron-sulfide alloys were selected as the counterface materials. Results indicate that the lowest friction coefficients under 0.22 can be obtained at 600 ℃ when rubbed against alumina. When rubbed against nickel-iron-sulfide alloys, are presented the lowest wear rates in the magnitude of 10-6 mm3/N·m, one order of magnitude lower than those when rubbed against ceramics. In the case of three rubbing pairs, the wear rates of the composite containing MoS2 present themselves inversely proportional to friction coefficients. With alumina ceramics used as a counterface, transfer films and glaze layers will form on the contact surface playing a main role in lubrication at high temperatures. However, when silicon nitride and nickel-iron-sulfide alloy are used, the lubricating transfer films appear not to be promi-nent.     

Microstructure and Optical Characterization of Magnetron Sputtered NbN Thin Films

Some fundamental studies on the preparation, structure and optical properties of NbN films were carried out. NbN thin films were deposited by DC reactive magnetron sputtering at different N2 partial pressures and different substrate temperatures ranging from –50 ℃ to 600 ℃. X-ray diffraction analysis (XRD) and scanning electron microscopy (SEM) were employed to characterize their phase com- ponents, microstructures, grain sizes and surface morphology. Optical properties inclusive of refractive indexes, extinction coefficients and transmittance of the NbN films under different sputtering conditions were measured. With the increase in the N2 partial pressure, δ-NbN phase structure gets forming and the grain size and lattice constant of the cubic NbN increasing. The deposited NbN film has relatively high values of refractive index and extinction coefficient in the wavelength ranging from 240 nm to 830 nm. Substrate tem- perature exerts notable influences on the microstructure and optical transmittance of the NbN films. The grain sizes of the δ-NbN film remarkably increase with the rise of the substrate temperature, while the transmittance of the films with the same thickness decreases. Ultra-fine granular film with particle size of several nanometers forms when the substrate is cooled to –50 ℃, and a remarkable aug- mentation of transmittance could be noticed under so low a temperature.